How to Add Product to Exterior Shower curb in MeasureSquare 8?
This article will guide you through how to add product to an Exterior Shower Curb in MeasureSquare 8.
Steps to Add Product to Exterior Shower Curb
Step 1 – DRAW ROOMS
Step 2 – Split Wall
- Using Split Wall Segment split the wall at the same width as the shower
Step 3 – Delete Wall Segments Between Rooms
- Right-click on the wall that was split, and select Delete Wall. Remember to delete both wall segments between the Shower Room & the Bathroom.
Bathroom Wall
Bathroom Wall
Shower Wall
Shower WallStep 4 – Stretch Rooms Together
- Click-and-hold the red handle in the center of the edge and slide until the edge of the Bathroom illuminates green
Step 5 – Draw Shower Curb using Elevation
- Click on Elevation in the ribbon and draw the Shower Curb inside of the Shower room.
Pro-Tip: When drawing the elevation, make sure the desired room is illuminated blue, to ensure proper control. Make sure to start on a wall (illuminated green) and use the distance from the edge to ensure perfect sizing. After the 1st click, use the crosshairs to ensure a straight line, across the shower. The more precise a drawing, the better quantities the system can provide.
Pro-Tip: When drawing the elevation, make sure the desired room is illuminated blue, to ensure proper control. Make sure to start on a wall (illuminated green) and use the distance from the edge to ensure perfect sizing. After the 1st click, use the crosshairs to ensure a straight line, across the shower. The more precise a drawing, the better quantities the system can provide.
Step 6 - Create Wall on Elevation
- Right-click on the bathroom-facing edge of the Shower Curb (Elevation) and select Create Wall to create the Exterior vertical surface of the Shower Curb
Pro-Tip: If the Create Wall process above is not followed, then there will only be one vertical surface of the curb, toward the Interior part of the Shower.
Pro-Tip: If the Create Wall process above is not followed, then there will only be one vertical surface of the curb, toward the Interior part of the Shower.
Step 7 – Adjust Height of Curb
- Adjust the Wall Height in the Property View to the desired measurement (e.g., 4"), as highlighted.
Step 8 - Apply Product
- Ensure the shower curb elevation is selected, then click View Wall. This will open shapes that represent the vertical surfaces of the curb to allow for product application.
- Select the desired product from the Product/Service panel.
- Drag and drop the product onto the surfaces desired.
- Ensuring the product is properly aligned and covers the intended area.
Pro-Tip: If trim is required at the edges of the curb, applying the product to those edges in 2D view, will apply them to the bottom of the vertical surfaces – but allow them to be seen in 2D. Applying the trim to the top edges of the vertical surfaces will render them correctly in 3D, but they will not be visible in 2D.
Pro-Tip: If trim is required at the edges of the curb, applying the product to those edges in 2D view, will apply them to the bottom of the vertical surfaces – but allow them to be seen in 2D. Applying the trim to the top edges of the vertical surfaces will render them correctly in 3D, but they will not be visible in 2D.
Step 9 - View in 3D
- Ensuring nothing is selected (or just the bathroom & shower room are selected) click on View3D to see the applied product in a 3D view.
- Within the 3D view, there will be a comprehensive view of the shower curb with the product applied.
Note: If you need further assistance, contact MeasureSquare Customer Support at +1-626-683-9188 or email support@measuresquare.com.
Related Articles
How Do I add Product to Exterior Walls in Measuresquare Mobile?
This article will show you how to add products to exterior walls in MeasureSquare Mobile This article applies to iPad iOS Step 1: takeoff your project as normal, creating your rooms and hallways. Step 2: use Rectangle by Drag tool to encompass your ...How do I design a bathroom or shower in MeasureSquare 8
In this video you will learn how to design a bathroom from start to finish in MeasureSquare 8. Including shower curb, accent tile band, working with hex tile, and wall tile. pertains to version .5393 or greaterHow do I add products to Project Items List in MeasureSquare 8?
In this article, we're going to show you how to add products from Product/Service list to Project Items list. This article applies to Windows MeasureSquare 8. Step 1: Right click on the product under Product/Service list > select Add to project items ...How Do I add Product to Exterior Walls?
This article will show you how to add products to exterior walls in MeasureSquare 8. Step 1: Select the Draw or Draw Rect tool, and draw a room encompassing your original area. Right click the outside room and select Send To Back. Step 2: Right-click ...How to apply Add-ons on Labor Products?
In this article, we will go over how to add Add-ons to a Labor Product. This article applies to MeasureSquare Mobile. Step 1: After you created your room and applied your Labor product to your room, Go to the Assignment Tab > Tap on the "i" icon on ...